Kitchen Plumbing Services for Remodels in Blackstone, IL
Kitchen plumbing for a remodel can be straightforward, like swapping out a faucet or hooking up a new garbage disposal, or it can be more extensive — moving your sink to a kitchen island, installing a new gas line for a range, adding a prep sink in a pantry, or roughing in a pot filler faucet. Each job varies in complexity, cost, and whether permits are needed. We manage every step.
Here’s a quick tip when planning: call us early, before cabinet installation. Moving a sink means rerouting drain lines and vent stacks, which is easiest when the subfloor is exposed. Gas line rough-ins for new appliances or islands should happen before cabinets go in to avoid chasing pipes later. Pot fillers require opening walls behind stoves, which is simpler before backsplash tile is installed. Scheduling plumbing work early keeps your remodel on track, especially with Illinois’ unpredictable weather.
We’re also available for kitchen plumbing repairs or upgrades outside remodels — faucet replacements, garbage disposal repairs, dishwasher connections, or installing fridge water lines. Remodeling is also a good chance to test your water heater’s capacity and clear any slow kitchen drains before the new cabinets go back in. Call 779-217-8763 anytime you need plumbing help.
Our Kitchen Plumbing Services
Sink and Faucet Installations
Whether you have an undermount sink that needs precise countertop cuts, a farmhouse-style apron front, or a simple drop-in, we handle the full installation. That includes fitting the drain assembly, strainer, P-trap, and connecting the water supply with durable braided stainless steel lines—not the brittle plastic tubing that fails prematurely. We install all types of faucets too, from single-hole to three-hole setups, testing everything thoroughly before we leave. If you’re relocating your sink, we take care of rerouting drains and vents with the proper permits and inspections.
Plus, if you’re adding or replacing a garbage disposal, we handle the connection alongside the sink install for your convenience.
Dishwasher and Appliance Hookups
Hooking up a dishwasher means connecting the hot water supply, routing the drain hose with a proper air gap or high loop to prevent backflow, and ensuring the electrical supply is ready — we coordinate with your electrician on that. For refrigerators with ice makers or water dispensers, we run a dedicated cold water line, properly supported and with an accessible shutoff valve behind the fridge. We also install instant hot water taps and under-sink water filtration or reverse osmosis systems, including faucet installation and line connections. For any appliance hookup in your kitchen, call us at 779-217-8763.
Gas Line Installation for Kitchen Appliances
Switching from electric to gas or adding a gas cooktop in a new island? We size the gas piping correctly based on your appliance’s BTU requirements, run a secure route from the gas meter or main line, install shutoff valves, connect the appliances with approved flexible lines, and pressure test everything to code. We also handle all permits and inspections so you’re covered. Check out our gas line services page for more info.
Important: gas line rough-ins for islands or relocated appliances should happen before cabinetry is installed. Trying to retrofit gas lines after cabinets are set is much more time-consuming and disruptive. Plan with your general contractor and us early to avoid delays.
Installing Pot Filler Faucets
A pot filler faucet mounted above your stove saves you from lugging heavy pots filled with water. Installing one requires running a cold water line inside the wall at roughly 56 to 60 inches above the floor and offset slightly from the stove center. This installation is simpler when walls are open during a remodel but can be done in finished kitchens with careful wall patching and repair. Give us a call to discuss what works for your space.
Island Sink Drain and Vent Solutions
Plumbing an island sink is trickier than a regular sink because you can’t tie its drain directly into a wall vent stack. Instead, we use an island loop vent or an air admittance valve (AAV) depending on local code requirements. Running hot and cold water supply is straightforward, but routing drains through the floor and venting properly takes experience. We've done island sinks in many Blackstone homes — reach out to talk through your island's layout before finalizing your plans.
Kitchen Plumbing Project Checklist
- Removing and installing sinks (undermount, farmhouse, drop-in)
- Installing faucets of all types
- Garbage disposal installation or replacement
- Connecting dishwasher water supply and drain
- Running water lines for refrigerator ice makers
- Installing gas lines for ranges, cooktops, or ovens
- Pot filler faucet rough-in and installation
- Under-sink water filtration and reverse osmosis systems
- Routing island sink drains and vents
- Upgrading shutoff valves throughout the kitchen
- Adding prep or bar sinks in pantries or kitchen islands
Tips for Timing Your Kitchen Plumbing
- Confirm sink placement before demolition: Sink relocation is the costliest plumbing change, so finalize location before ordering cabinets.
- Complete gas rough-ins before cabinetry: Run new gas lines for islands or relocated ranges ahead of cabinet installation.
- Install pot fillers before backsplash: Open walls are much easier to work with than finished tile.
- Replace old shutoff valves while exposed: Swap failing gate valves for reliable ball valves during plumbing access.
- Run refrigerator water lines before counters go in: It’s simpler to install before countertops are set.
Frequently Asked Questions About Kitchen Remodeling Plumbing
Definitely. It’s the more complicated plumbing change because island sinks need special venting methods, like an island loop vent or an air admittance valve, to meet code. Water supply lines are straightforward, but the drain and vent routing through the floor takes planning. We’ve done plenty of island sinks here in Blackstone — call us to chat about your design before you set it in stone.
If you’re just replacing fixtures in the same spot (like a faucet or disposal), typically no permit is needed. But if you’re rerouting drains, adding new supply lines, working on gas piping, or moving plumbing fixtures, permits are required. We handle all permit applications and inspection coordination as part of our service.
Yes, and it’s best done early in the remodel when walls are open. We take care of gas line installs for ranges, ovens, and cooktops — sizing pipe accurately, pressure testing, and handling permits. Make sure to schedule your gas rough-in before cabinetry installation to avoid costly rework.
Absolutely. We work alongside general contractors and designers as the plumbing trade partner for kitchen remodels. We coordinate rough-in and finish phases according to the overall construction timeline and handle permits and inspections smoothly. Early communication helps keep everything on schedule — call us to get on your project team.